The first step is to check the IP address of your Synology NAS. To do this, open the Control Panel and go to Network > Status. The IP address should be listed under the “WAN” section. If it isn’t, then your VPN isn’t working and you’ll need to troubleshoot the issue.
Next, try accessing some services that are normally blocked by your ISP or country. For example, if you’re trying to access Netflix USA from outside the USA, then you can use the DNS Leak Test tool to see if your DNS requests are being leaked. If they are, then that means your VPN isn’t encrypting them properly and isn’t providing yo with adequate privacy protection.
Finally, it’s also worth checking out our list of Sites That Block VPNs . Some popular sites like Netflix , BBC iPlayer , and Pandora have been known to block certain types of VPN traffic . If you’re having trouble accessing one of these sites while using a Synology NAS , then chances are that your particular VPN is being blocked .
Setting up a VPN connection to your Synology NAS can be done in a few simple steps. First, you’ll need to create a new user account specifically for VPN access. Next, open the DSM (DiskStation Manager) web interface and go to Control Panel > External Access > VPN. Select OpenVPN from the list of available protocols and click ‘Create’.
Now enter a name for your new connection and fill in the required information such as server address, port number, encryption method, etc. You can also specify which users will have access to this connection by clicking ‘Permissions’. When finished, click ‘OK’ to save your changes.
The final step is to download and install the OpenVPN client on your computer or mobile device. Once installed, launch the client and enter the same login credentials that you used when creating the user account earlier. After connecting successfully, you should now be able to access your Synology NAS as if you were on your local network!
To use a Synology NAS as a VPN server, you will need the following:
A Synology NAS running DSM 5.2 or higher
A router that supports PPTP or OpenVPN protocols
A static IP address for your Synology NAS
The first thing you need to do is set up your router to forward traffic to your Synology NAS. To do this, you will need to login to your router’s web interface and look for the port forwarding section. Add a new rule that forwards traffic on port 1723 (for PPTP) or port 1194 (for OpenVPN) to the IP address of your Synology NAS. Next, log into DSM and go to Control Panel > Network > Network Interface tab. Click Create > Create VPN Profile.
For the Connection Type, select either PPTP or OpenVPN depending on which protocol you configured on your router. For Server Address, enter the WAN IP address of your router. If you are using OpenVPN, be sure to check Enable LZO Compression and Disable IPv6 options under Advanced Settings. Enter a Username and Password that will be used to authenticate with the VPN server. When finished, click Apply at the bottom of the page.’Now open Network Center and go to Connections tab.’
Check Show All so you can see all of the available connections.’ Select Edit next top right corner of the screen.’ Go through each setting and verify it matches what we have here.”When ready click Save then Connect.’If everything was entered correctly,’you should now be connected
One common question we get asked is whether it’s possible to use a VPN on a Synology NAS. The short answer is yes! In this blog post, we’ll show you how to set up a VPN on your Synology NAS in just a few minutes.
The first thing you need to do is create a user account for the VPN service. To do this, open the Control Panel and go to User > Accounts > Create User. Enter a username and password for the VPN account and click “OK”.
Now go to Network > Interface > Create > Create VPN Profile. Select “OpenVPN” as the protocol and enter the following settings:
– Name: Enter a name for the profile (e.g., MyVPN)
– Server Address: Enter the IP address or domain name of your VPN server (you can find this in the control panel of your VPN provider)
– Port Number: Leave at default (1194) unless instructed otherwise by your provider Status: Enable
Click “OK” when finished and then select the user account you created earlier from the list of users under “Authorized Users”. Click “Apply�� at the bottom of the page when finished.”’
Thank your for reading!